Aluminium Carburetor Mounts / Spacers 40 mm / 45 mm / 48 mm / 50 mm

Fitting Material
SPCR
9503341183384
Select an option
    Delivery time: In stock and ready to ship
Add to cart
  • Description
  • More

Machined from solid aluminium (or aluminum if you prefer...). and can be used in combination with the Cosworth buffer mounts.

Grooved on both sides to accept an O-Ring, these "spacers" ensure an airtight seal between carburettor and manifold.

For the best result, we strongly advise the combination with the Cosworth buffer mounts.

Install the o-rings in the spacers, then install your carb(s) and install the Cosworth mounts using a Nyloc nut (NOT included in the standard set!) and set the distance between the cups to 2 millimeter, using a normal feeler gauge.
The buffer is now set to the correct tension to dampen vibrations but not allowing air leaks.

These spacers are supplied in sets of 2 which is enough for one carburettor like a Dellorto DHLA, Solex ADDHE, Weber DCOM or Weber DCOE.

Also suitable for the Weber DCO/SP but that will require fitting kit FK0002.

The plates are some 6 mm think.

The mounting holes measure some 8.5 mm in diameter and are spaced at 72 mm center-to-center.

Sold, and priced, per pair and 2 O-Rings are included per spacer.

These spacers are specifically sized to work with carburetors with a corresponding throttle plate diameter so please check carefully which size you require.

We have the following sizes available:

  • 40 mm
  • 45 mm
  • 48 mm
  • 50 mm

Replacement o-rings can be purchased HERE.

For your convenience you can order the Cosworth buffer mounts and high quality Stainless Steel Self-Locking M8 nuts right along with it.

Please note that you will need to make your selections through the drop-down menu's right above the Add to Cart button.

Aluminium Carburetor Mounts / Spacers 40 mm / 45 mm / 48 mm / 50 mm

Aluminium Carburetor Mounts / Spacers 40 mm / 45 mm / 48 mm / 50 mm

Machined from solid aluminium (or aluminum if you prefer...). and can be used in combination with the Cosworth buffer mounts.

Grooved on both sides to accept an O-Ring, these "spacers" ensure an airtight seal between carburettor and manifold.

For the best result, we strongly advise the combination with the Cosworth buffer mounts.

Install the o-rings in the spacers, then install your carb(s) and install the Cosworth mounts using a Nyloc nut (NOT included in the standard set!) and set the distance between the cups to 2 millimeter, using a normal feeler gauge.
The buffer is now set to the correct tension to dampen vibrations but not allowing air leaks.

These spacers are supplied in sets of 2 which is enough for one carburettor like a Dellorto DHLA, Solex ADDHE, Weber DCOM or Weber DCOE.

Also suitable for the Weber DCO/SP but that will require fitting kit FK0002.

The plates are some 6 mm think.

The mounting holes measure some 8.5 mm in diameter and are spaced at 72 mm center-to-center.

Sold, and priced, per pair and 2 O-Rings are included per spacer.

These spacers are specifically sized to work with carburetors with a corresponding throttle plate diameter so please check carefully which size you require.

We have the following sizes available:

  • 40 mm
  • 45 mm
  • 48 mm
  • 50 mm

Replacement o-rings can be purchased HERE.

For your convenience you can order the Cosworth buffer mounts and high quality Stainless Steel Self-Locking M8 nuts right along with it.

Please note that you will need to make your selections through the drop-down menu's right above the Add to Cart button.

Aluminium Carburetor Mounts / Spacers 40 mm / 45 mm / 48 mm / 50 mm

Aluminium Carburetor Mounts / Spacers 40 mm / 45 mm / 48 mm / 50 mm

Aluminium Carburetor Mounts / Spacers 40 mm / 45 mm / 48 mm / 50 mm


Aluminium Carburetor Mounts / Spacers 40 mm / 45 mm / 48 mm / 50 mm

Aluminium Carburetor Mounts / Spacers 40 mm / 45 mm / 48 mm / 50 mm

Aluminium Carburetor Mounts / Spacers 40 mm / 45 mm / 48 mm / 50 mm

Aluminium Carburetor Mounts / Spacers 40 mm / 45 mm / 48 mm / 50 mm

!